Speed Queen washers are here to tackle your laundry load, but when glitches occur, deciphering error codes is key. Let’s unravel the mystery of Speed Queen washer fault codes together. With this guide, you’ll be equipped to troubleshoot effectively and get your laundry back on track.
Demystifying Speed Queen Washer Fault Codes: A Quick Overview
Your Speed Queen washer communicates through error codes. Let’s shed light on some common codes and their meanings:
Alrm – Break In Alarm Door
This code signifies an issue with service door or coin vault switches. Check these switches for proper operation.
door – Door Open Indicator
If the door is open, close it. If the door isn’t open but the code persists, inspect the door switch for improper wiring.
E:00 – General Error
A general error suggests re-aiming the micro-wand. Try re-aiming the micro-wand and retry.
E:01 – Proximity Error
This code occurs when the micro-wand is incorrectly aimed at the infrared communicator. Re-aim the micro-wand for accurate communication.
E:02 – IR Communication Disconnection
This code indicates that the micro-wand was removed before communication completed. Re-aim the micro-wand and try again.
E:05 – Invalid Value Communication
When an invalid code is downloaded from the micro-wand to the electronic control, this error arises. Re-aim the micro-wand and retry.
E:07 and E:08 – Inoperative Control
These codes point to an inoperative control. The control board needs replacement.
E:09 and E:0B – Proximity Error
Similar to E:01, these codes result from removing the micro-wand before communication finishes. Re-aim the micro-wand and retry.
E:0C – IR Communication Disconnection
Similar to E:02, this code results from premature removal of the micro-wand. Re-aim and try again.
E:0d – Pressure Switch Error
Check fill and drain hoses for clogs or kinks, and inspect the electrical circuit. Replace any defective components.
E:0F – IR Communication Programmed Off
To resolve this error, reprogram the infrared communicator, manually enable IR on the control, and re-aim the micro-wand.
E:dF – Drive Failure
In case of this error, check the motor and tachometer circuit. Disconnect power, restart the machine to reset.
E:dL – Door Lock Error
Open and close the door. Check the door lock and switches for defects.
E:dO – Door Open During Running Cycle
Make sure the door is properly closed. Check the door lock and switches for issues.
E:dr – Drain Error
This error occurs when the maximum drain time is exceeded or water is still detected at the end of the spin cycle.
E:FL – Fill Error
If the pressure switch fails to open in 30 minutes during any fill-agitate cycle, this error is triggered.
E:HT – Heater Error
Replace the bad heat circuit component to resolve this issue.
E:OP – Open Temperature Sensor Error
Replace the temperature sensor to fix this error.
E:Pr – Pressure Switch Sequence Error
Replace the pressure switch if this error persists.
E:SH – Shorted Temperature Sensor Error
Replace the temperature sensor to resolve this error.
E:SP – SPI Communication Error
This error is caused by a transformer being unplugged or incorrect wiring to the motor control.
E:Ub – Unbalance Error
Redistribute the load and rerun the cycle.
EC Codes – Communication Errors
These codes indicate communication problems. Check connections, ensure data accuracy, or replace faulty components.
EI Codes – Communication Errors
Similar to EC codes, these suggest communication issues. Re-aim the micro-wand and verify data for the correct machine type.
ERR / Err – Coin Error
Inspect the coin drop area for obstructions.
OFF – Break Down In Alarm Shutdown Error
This code relates to service door or coin vault switch problems.
Swift Solutions: Troubleshooting Speed Queen Washer Woes
Here are some steps to troubleshoot common issues:
- Power Cycle: Turn off the washer, unplug it, wait, and restart.
- Firmware Update: Ensure your washer’s firmware is up to date.
- Check Connections: Loose wires can cause errors. Verify all connections are secure.
- Clean and Maintain: Regularly clean lint filters, and washer tubs, and check hoses for obstructions.
- Replace Faulty Parts: If needed, replace temperature sensors, control boards, or other malfunctioning components.
Mastering the Spin Cycle: Expert Tips
Keep your laundry days seamless with these tips:
- Regular Maintenance: Routine checks and cleaning prevent many issues.
- Professional Help: If errors persist, consult the user manual or contact Speed Queen customer support.
Wrapping Up:
Speed Queen washer fault codes may appear daunting, but this guide equips you to tackle them. With the right knowledge, you’ll troubleshoot effectively and enjoy hassle-free laundry days. If you’re hungry for more laundry insights, follow us on Instagram for expert advice and tips!