Fault Codes For Speed Queen Dryer
Alrm, which stands for “Break-In Alarm Door,” is a service door or coin vault switch.
E:00 – General Error – Re-aim the micro-wand and try again.
E:01 – Proximity Error – The micro-wand is pointed at the infrared transmitter in the wrong way. Try again after re-aiming the micro-wand.
E:02-IR transmission Disconnection-The micro-wand was taken away before the transmission was finished. Try again after re-aiming the micro-wand.
E:05: bogus Value Communication. This mistake happens when the micro-wand sends a bogus code to the electrical computer. Try again after re-aiming the micro-wand.
E:07: Control is not working. Replace the control board.
E:08: Control is not working. Replace the control board.
E:09: Proximity Error: The micro-wand was taken away before the connection was finished. Try again after re-aiming the micro-wand.
E:0B-IR conversation Disconnection-The micro-wand was taken away before the conversation was finished. Try again after re-aiming the micro-wand.
E:0C – IR contact Disconnection – Micro-wand was removed before contact was finished. Try again after re-aiming the micro-wand.
E:0F-IR Communication Was Turned Off-Reprogram the infrared transmitter to be on and turn the IR on button on by hand. Try again after re-aiming the micro-wand.
E:OP: Open Temperature Sensor Error. Temperature sensor needs to be replaced.
E:SH – Shorted Temperature Sensor Error – Temperature sensor needs to be replaced.
EC:00: General Communication Error: There’s a problem with communication. Try card once more.
EC:02 – Time Out Error – Problem with communication. Try card once more.
EC:03: Wrong machine type. Invalid command code. Before you download, make sure the info for your machine type is up to date.
EC:05: Invalid or Out-of-Range Data or Wrong Machine Type. Before you download, make sure the info for your machine type is up to date.
EC:06: Wrong machine type. Invalid data code. Card might need to be changed out. Before you download, make sure the info for your machine type is up to date.
EC:09: Corrupted Data Error: There is a problem with communication. Try card once more.
EC:0A: Invalid Machine Type: Machine type is wrong. Before you download, make sure the info for your machine type is up to date.
EC:19: No Communication with Card Reader. Turn off the unit and turn it back on to try again. The reader or control board is broken if the mistake keeps happening.
EC:20: The card can’t be read. Clean the contacts on the chip card and the card reader. If the mistake keeps happening, the card may be broken.
EC:21 – Mismatched Security ID – Wrong card. Use the proper security code on the card.
EC:22-Site Code Mismatch-Incorrect card. Use the proper security code on the card.
EC:23: Card’s Maximum Value Has Been Reached: Use a card that doesn’t go over the maximum value.
EC:24: There isn’t enough space on the card. Download the card’s data to a PC and clear the card so it can be used again.
EC:25: Card Reader Doesn’t Work. You may need to change the card reader.
EC:26: Error writing to card. Try card again. If the mistake keeps happening, the card may need to be changed.
EC:27: Diagnostic Test Card Write Failure: The card reader may need to be changed.
EC:28 – Diagnostic Test Card Write Failure – You may need to change the card reader.
EC:29: Diagnostic Test Memory Test Failed. You may need to update the card reader.
EC:2A: Diagnostic Test Card Interface Failed. The card reader may need to be changed.
EC:2b – Diagnostic Test Flash Failure – You may need to change the card reader.
EC:2C: Bad Biberon or non-Biberon device. You may need to change the card reader.
EC:2d: Firmware Update Did Not Work S/W (software) Not Intact: You may need to change the card reader.
EC:2E: Firmware Update Did Not Work S/W (software) Not Intact: You may need to change the card reader.
EC:2F – Firmware Updates, S/W Not Intact – You may need to update the card reader.
EC:30: Timeout Error: The card reader may need to be changed.
EC:31: A hotlisted card is put into the reader. If the card is on the hotlist, the card will be destroyed.
EC:50- – Loyalty Purse Read Error – Try card again. If the mistake keeps happening, the card may need to be changed.
EC:56: Loyalty Purse Write Error. Please try card again. If the mistake keeps happening, the card may need to be changed.
EI:00 – General Communication Error – Re-aim the micro-wand and try again.
EI:01 – Bad Transmission: Re-aim the micro-wand and try again.
EI:02: Device Timeout. Re-aim the micro-wand and try again.
EI:03: Wrong machine type, invalid command code. Before you download, make sure the info for your machine type is up to date.
EI:04 – Expecting Upload Request – Re-aim the micro-wand and try again.
EI:05 – Invalid or Out-of-Range Data – Wrong type of machine. Before you download, make sure the info for your machine type is up to date.
EI:-06 – Invalid Data Code – Wrong type of machine. Before you download, make sure the info for your machine type is up to date.
EI:07 – Error Writing to RTC – Control may need to be changed.
EI:08 – Error Writing to EEPROM – Control may need to be changed.
EI:09 – CRC-16 Error – Re-aim the micro-wand and try again.
EI:0A: Invalid Machine Type/Proximity Error: Machine type is wrong. Before you download, make sure the info for your machine type is up to date. Try again after re-aiming the micro-wand.
EI:0F – Invalid Wake-up of IR Disabled – Manually allow IF on control and re-aim micro-wand, then try again.
ERR / Err – Coin Error – Check the coin drop place and get rid of any things that are in the way.
OFF – Break Down In Alarm Shutdown Error – Service door or coin vault switches.
OP-Open Thermistor-Replace the thermistor.
Most Significant Digit Lit – Network Communication mistake – Wait for the mistake to go away. If the mistake doesn’t go away in one minute, turn off the unit’s power and then turn it back on. If the problem still happens, you may need to change the control network board.
SH: The Thermistor is shorted. Replace the thermistor.
network board.