Every home has a washing machine because it is useful and because everyone has one. It may have an error code sometimes. Some error codes can be fixed at home, but others need to be fixed by a professional. This post will tell you all of the error codes for your Hisense washing machine, which I think will help you a lot. If you think this post will help other people, please share it.
Hisense washing machine error codes
| ERROR CODE | PROBLEM |
|---|---|
| F01 | Water inflow fault |
| F03 | Drainage fault. Not fully drained within 6 minutes. |
| F04 | Heating Error. The heater is out of order. Give an alarm after the washing course ends. |
| F05 | Electronic module fault, overflow, or too much foam. |
| F06 | No Motor Speed Feefback Error. The rotation speed is not set as 0, but no rotation speed is detected within 3s or the rotation speed is below 20rpm, 5 attempts. |
| F07 | Motor SCR Short Circuit Error. 1. The rotation speed is not set as 0, but the measured rotation speed>set rotation speed+80, and lasts for 3 seconds 2. The rotation speed is set as 0, but the rotation speed rises rather than declines, exceeding 10 turns within 3 seconds. |
| F08 | Heater Circuit Error. The main control detected a heater circuit failure. These failure modes are checked before the cycle starts and after the spinning steps. |
| F12 | Heater Circuit Error. The main control detected a heater circuit failure. These failure modes are checked before the cycle starts and after the spinning steps. |
| F13 | Door lock fault. Start the program for 20 sec and unlock the washer door(PTC) to check whether the door is closed. |
| F14 | EEPROM Error. The central control unit (CCU) receives its data from an EEPROM onboard the CCU, if there is an error reading this data it will cause this error. |
| F15 | F17 indicates no water coming into the condensing chamber during drying. Unplug the appliance. Take the top off. Check to see if the condensing chamber below the heating chamber is blocked. |
| F21 | User Interface Error. -Check the wiring connection to the display module. -Check the display module. -Check the control unit (CCU). |
| F23 | FWL Sensor Error. 1. The FWL sensor is out of order 2. When water level frequency maintains the condition of below 10 kHz and over 30 kHz. |
| F24 | Water Level Reaches Overflow Level. Water is overflowing. (water level frequency is over 36.8kHz). If F24 is displayed, the drain pump will operate to drain the water automatically. |
| F26 | Pump Driver Failure. If the CCU detects during the wash cycle that the triac of the pump is defective it will display this failure. Check the resistance of the pressoswitch. A failure of the pressosswitch could also cause the code. If OK start start service test to check CCU. İf the ailure occurs replace the CCU. |
| F27 | Reversing relay failure. If the CCU detects that the motor is possible to rotate only in one direction this failure is displayed. – Check the harness of the motor. – Check the CCU. |
| F28 | Tapped Field Failure. If the CCU is not able to switch ON the tapped field of the motor this failure code is displayed. -Check if the correct motor is built in. -Check the resistance of the fields of the motor. -Check the harness between the motor and CCU. -If the points above are OK replace the CCU. |
| UNB | Unbalance alarm. Press the “Power Supply” key for 3 sec to turn off the machine. |
| FH | Water supply fault. The water tap is closed. |
| FP | Draining fault. Clean pump. |
| FA | Water Stop fault |
| Fod | Over foaming fault |
Hisense Washing Machine Troubleshooting
| TROUBLE | CAUSE |
|---|---|
| The washing machine will not start and no indicator lamps are on. | Check whether: The mains plug is inserted into the socket and the power is switched “ON”. The wall socket is functioning correctly(use a table lamp or similar appliance to test it). |
| The washing machine will not start. | Check whether: The door is properly closed (child safety). The “Start /Pause” button has been pressed. The Water tap is opened and press the” Start/Pause” button. |
| The appliance stops during the program. | Check whether: The “Rinse Hold ” indicator lamp lights up; terminate this option by pressing the “Start/Pause” button or by choosing and starting the “Drain” program. Another program has been selected and the “Start/Pause” button has not been pressed. Reselect the desired program and press the “Start/Pause” button. |
| Residue from detergent and additives left in the detergent drawer at the end of the wash. | Check whether: -The cover grid of the softener chamber and the separator of the main wash chamber are correctly installed in the detergent dispenser and all parts are clean. -Sufficient water is entering. The mesh filters of the water supply could be blocked. -The position of the separator in the main wash chamber is adapted to the use of powder or liquid detergent. |
| The machine vibrates during the spin cycle. | Check whether: -The washing machine is level and standing firmly on all four feet. -The transport bolts have been removed. Before using the machine, it is imperative that the transport bolts are removed. |
| The final spin results are poor. | -If the laundry is still too wet at the end of the cycle, remove some articles of laundry and repeat the spin cycle. -Excessive foam formation may prevent spinning. Use the correct amount of detergent. -Check that the spin speed selector has not been set to ” 0″. |
These are just some of the most common error codes. The specific error codes that your washing machine displays may vary depending on the model.
If you see an error code on your Hisense washing machine, it is important to first check the user manual for the specific meaning of the code. The manual will also provide troubleshooting tips that you can try.
If you are unable to fix the problem yourself, you should contact a qualified technician for assistance.
Here are some additional tips for troubleshooting Hisense washing machine error codes:
- Check the power supply to the washing machine. Make sure that the washing machine is plugged in and that the power is turned on.
- Check the water supply to the washing machine. Make sure that the water supply is turned on and that there is no blockage in the water lines.
- Check the drain hose for blockages.
- Clean the filters in the washing machine.
- Reset the washing machine by turning it off and then on again.
If you have tried all of these troubleshooting steps and the error code is still displayed, then you should contact a qualified technician for assistance.