Hello, fellow technology nerds! You know how annoying it may be if you’ve ever encountered an error code on your HP printer. We’ve got your back, so don’t worry! In this thorough guide, we’ll decode those mysterious problem codes and provide you workable fixes to get your HP printer running again. Let’s have a look at HP printer issues in detail.
Introduction: Decoding HP Printer Errors
Modern technology brings us amazing conveniences, but every now and then, our trusty HP printers might throw a curveball with an error code. But don’t fret! We’re here to unravel the mysteries behind these codes and empower you to troubleshoot like a pro.
HP Printer Error Code List With Solutions pdf: Download
HP Printer Error Code List With Solutions
| Error Code | Cause | Solution |
|---|---|---|
| 1E, E7 | Water Level Sensor Issue | Please look for any blockages, cracks, or degeneration in the pressure hose system. The pressure sensor should be changed if no damage is discovered and the connection is sound. |
| 3E, 3E1, 3E2, 3E3, 3E4, EA, EB | Motor Defect | Could be an open/short circuit (please check wind resistance), a PCB fault, or a loose connector. |
| 3E1 | Motor Overload | Ensure there isn’t too much laundry in the appliance, the hall sensor terminal isn’t connected, or a possible PCB fault. |
| 3E2 | Motor Driving Error | The motor driving error from the PBA is weak, unstable relay operation. We recommend replacing the Motor PCB. |
| 3E3 | Quiet-Drive Motor Error | Faulty motor hall sensor, faulty PCB connection, or the Quiet Drive motor cover is out of place. |
| 3E4 | Quiet-Drive Motor Defect | The PCB Housing terminal is not connected, there’s a PCB fault, or the Quiet-Motor drive is faulty. |
| 4E, E1 | Water Supply Error (only occurs after 10 mins when the pressure sensor is not detecting the unit filling with water) | Inspect the hoses for kinks, the inlet filters inside the water valve’s end, the water valve coil resistance, which should be 4 to 5 k, and the hose from the drum to the sensor. Samsung recommends a minimum water pressure of 0.5 bar and a maximum of 8 bar. This MUST be replaced if it is split or cracked. |
| 4E1, 4ED | Water Temperature Issue | Check to ensure the water hose is connected to a cold supply. It must NOT be connected to a hot supply. |
| 4E2 | Water Temperature Error | The water is too hot for the selected wash. |
| 5E, E2 | Water Drain Error (only occurs after 10 mins when water is not draining from the appliance) | Check the drain pump filter for any blockages (e.g. coins, hair clips, lint, etc.), and check the drain hose and connection for any blockages or kinks. |
| 6E | Water Heater is Not Functioning | Check the heater resistance which should be around ~27Ω. |
| 8E | Over Current Error | Switch the appliance off at the mains and wait 30 seconds. Switch the appliance on and try again, if the appliance has an inverter motor check windings are not open-circuit- causing juddering. |
| 8E1 | MEMS Sensor Error | Check the connections to the MEMS sensor which is mounted on top of the tub. All they’re all secure then replace the sensor. |
| 9E1, 9E2, PH1, Plo | Power Error | Check the supply voltage, check for loose power connectors or any with contact defects, and check for defective noise filters and fuse. |
| AE, 13E | Signal Communication Error (between the Main PCB and Sub PCBs) | Check all the connectors on the Main PCB and Sub PCBs. |
| bE | Motor TRIAC Short Error | Switch off the power and then reconnect and try again. If the error persists then replace the PCB. |
| bE1, 12E | Power Button Fault | The power button held in for more than 13 seconds. |
| bE2, 14E | Control Button Fault | Any button (other than the power button) held in for more than 30 seconds. |
| bE3, 18E | Switch Error | There is a relay fault. |
| CE, E8 | Cooling Error (temperature of the water has not dropped below 55°C in 30 minutes after the washer cooling operation) | Check if the water supply is connected to the hot and if so change to a cold-only feed, check that the hot/cold water supply is not switched over, if the first two are OK then check the heater temperature sensor. |
| dE, Ed | Door Open Error (door not closed correctly/properly) | Door Open Error (door not closed correctly/properly). |
| dE1 | Door Lock Switch Error | Check that the door is closed, check the switch for any damage and if so please replace it. |
| dE2 | On/Off Switch Error | Excessive heat build-up in the coil due to the button being operated continuously |
| FE | Fan Error (Dryer or Air Refresh fan fault) | Check the start condenser/capacitor and fan motor connections, and check to see if the fan is hammed if no other fault then replace the start condenser/capacitor. |
| H1 | Incorrect Water Temperature/Water Temperature rises quickly | Check the temperature sensor, check the pressure switch and hose. |
| HE | Abnormal water temperature | The temperature sensor has detected temperatures over 100°C. |
| HE1, E5 | Water Heater Error (this occurs if the water temperature has not reached 50°C in 20 minutes or does not rise more than 2°C) | Check the heater resistance which should be ~27Ω. |
| HE2 | Dryer Heater Error (occurs if the dryer heater circuit is open circuit) | Check heater TCOs. One is resettable. if it needs to be reset; check the fan for correct operation, check the condenser water valve operation, and check the condenser for blockages. |
| HE3 | Steam Function Fault | Check steam function and TCOs. |
| HOT | Appliance Too Hot (occurs if the dryer is turned off early) | This is not a fault – the appliance fan will continue to run until the appliance is cool enough for the washing to be removed. The door will unlock when it is safe. |
| LE, LE1, E9, 11E | Water Leak (low water level detected during the cycle) | Check that the level of the drain hose is not lower than the base of the Samsung washing machine. |
| OE, E3 | Overflow Error (too much water/foam has entered into the appliance) | Too much washing powder/liquid may have been added. Turn the power off to the appliance, wait 30 seconds, and then turn on again. The drain pump should kick into action to drain the appliance. Also, check the pressure system for any debris/foam. |
| OF | Overflow Abnormal (water has reached the overflow level) | Check for any water valves which have stuck in the open position, and check for debris/foam in the pressure system. |
| Sud | Excess Foam Detected | This is a normal operation. The appliance will normally cure this condition on its own however if it doesn’t then run either an “Eco drum clean” or a 90°C cotton cycle with no detergent and no washing inside. If the problem persists then please check the pressure system and sump for any debris. |
| t1, t2, tSt | Appliance In Test Mode | Switch the appliance off at the mains and wait 30 seconds. Then, switch it back on and try again. |
| tE, EC | Temperature Sensor Abnormal Issue | Switch off the power and reconnect and try again. Check all the temperature sensors for relative continuity. |
| tE1 | Water Heater Temp Sensor Defective | Check the connections to the sensor and PCB, and check resistance which should be ~12.8kΩ |
| tE2 | Fan Housing Duct Sensor Defective | Check the connections to the sensor and PCB, and check resistance which should be ~12.8kΩ |
| tE3 | Condenser Duct Sensor Defective | Check the connections to the sensor and PCB, and check resistance which should be ~12.8kΩ |
| UC | Excessive Fluctuation In The Supply Voltage (voltage has fluctuated outside 176-286vAC) | Check that the supply voltage is within specifications, and reset the power supply to clear the error. If the error cannot be reset then please replace the main PCB. |
| UE, E4 | Unbalanced Error (the washing load in the drum is unbalanced i.e. clothes may have got trapped inside a large towel and resting on one side of the drum) | The washing machine may be interrupting the spin cycle as part of routine operation for security reasons. Washing should be distributed more equally. Check the condition of the springs, the shock absorbers, and the weights and balancers. |
Common HP Printer Error Codes and Their Meanings
Error Code 0x610000f6: Paper Jam
When your printer’s complaining about a paper jam, it’s time to play detective and inspect those paper paths. Sometimes a tiny piece of paper might be causing a ruckus.
Error Code 0xc19a0003: Ink System Failure
Oh no, ink system failure! This might be due to a glitch in the matrix. Let’s explore ways to reset the ink system and get those ink cartridges back in harmony.
Error Code 0x83c00009: Missing or Damaged Cartridge
Your printer’s fussing about missing or damaged cartridges? Let’s make sure those ink reservoirs are snug and secure.
Error Code 0x61000016: Misaligned Print Head
A misaligned print head can cause chaos in your printouts. Fear not, we’ll guide you through the process of realigning it.
Error Code 0xc0000034: Boot Device Not Found
Boot device not found? This might sound like a computer error, but your printer’s just as tech-savvy. We’ll help you navigate this glitch.
Error Code 0x61000032: Out of Paper
When your printer claims it’s out of paper but you know it’s not, let’s investigate what’s causing the confusion.
Error Code 0xc4eb827f: Printhead Issue
Printhead problems? It’s like your printer’s having a bad hair day. We’ll guide you through cleaning and resolving these pesky issues.
Error Code 0x61011bed: Printer Offline
Is your printer sulking in the corner, offline and unresponsive? Let’s coax it back to life and explore the reasons behind this offline escapade.
Error Code 0xc19a0020: Ink System Failure
Ink system on strike? This error might need a gentle reset and some ink cartridge TLC to get your printer back in the game.
Error Code 0xc05d1281: Ink System Supply Error
An ink system supply error? Let’s dive into the ink supply realm and troubleshoot this ink conundrum together.
Error Code 0x610000f2: Printer Door Open
If your printer’s convinced that its door is open when it’s not, it’s time for some door-checking detective work.
Error Code 0x83c0000a: Ink Cartridge Problem
Ink cartridge problems causing a ruckus? Let’s investigate if it’s a cartridge issue or something more.
Error Code 0xc19a0005: Ink System Failure
Another ink system failure? No worries, we’ll guide you through potential solutions to keep those ink levels happy.
Error Code 0xc19a0013: Ink System Failure
Ink system still giving you a hard time? This error might be a bit stubborn, but we’ve got tricks up our sleeves to tackle it.
Error Code 0xc19a0043: Printhead Problem
Is Printhead acting up again? Let’s roll up our sleeves and explore ways to address this issue and get those crisp prints back.
Here are some general tips for troubleshooting HP printer errors:
- Restart the printer. This will often fix simple errors.
- Check the printer’s ink levels. If the ink levels are low, replace the ink cartridges.
- Make sure that the printer is properly connected to your computer.
- Update the printer’s firmware. This can fix known bugs and improve the printer’s performance.
- Contact HP support for assistance. If you have tried all of the above and you are still unable to fix the error, contact HP support for further assistance.