Electrolux Basic Washing Machines come equipped with a variety of error codes designed to alert users to potential issues and malfunctions that may arise during the washing process. These error codes serve as valuable troubleshooting tools, helping users diagnose problems and take appropriate actions to ensure the proper functioning of their washing machines. Here are some common Electrolux Basic Washing Machine error codes along with their meanings:
Electrolux Basic Washing Machine Error Codes
| Error Code | Error Showes | Possible Problem | How to fix |
|---|---|---|---|
| Fault Code / Error Code E10 appears. The LCD display RINSE + flashes | There is no water flows | The water tap is closed. | Open the water tap. |
| The filter in the screw connection of the inlet hose is blocked. | Close the water tap. Unscrew the hose from the tap, remove the filter and clean under running water | ||
| Water tap is blocked with limescale or is faulty | Check the water tap and have it repaired if necessary. | ||
| Replace the inlet valve inside the washing machine | |||
| The fault Code / Error Code E20 appears. The RINSE display flashes. | The washing is not sufficiently spun. Water is left in the drum. | The drain hose is kinked. | Remove the kink. |
| Maximum pump head (discharge height 1m from the appliance’s base) is exceeded. | Contact your local Service Force Centre. For pumping heights over 1m a conversion kit is available as a special accessory. | ||
| The drain pump is blocked. | Switch off the appliance and pull out the main plug. Clean the drain pump | ||
| The fault Code / Error Code E40 appears. The display MAIN WASH flashes | The door is not correctly closed. | Close the door correctly. Start the programme again. |
Electrolux Washing Machine Error Codes, EWFM series, AWF series:
| Error Code | Error Showes | Possible Problem | How to fit |
|---|---|---|---|
| E10 | The water tap is closed. | Open the water tap. | Call EPL Appliance Repairs 1300 EPL 000 |
| The inlet hose is squashed or kinked. | Check the inlet hose connection. | Call EPL Appliance Repairs 1300 375 000 | |
| The filter in the inlet hose is blocked. | Clean the water inlet hose filter. | Call EPL Appliance Repairs 1300 EPL 000 | |
| E20 | The drain hose is squashed or kinked. | Check the drain hose connection. | Call EPL Appliance Repairs 1300 375 000 |
| The drain filter is clogged. | Clean the drain filter. | Call EPL Appliance Repairs 1300 EPL 000 | |
| E40 | The door has not been closed. | Close the door firmly. | Call EPL Appliance Repairs 1300 375 000 |
| The door is not properly closed | Close firmly the door | Call EPL Appliance Repairs 1300 EPL 000 | |
Electrolux Washing Machine Error Codes ENV series
| Error Code | Error Showes | Possible Problem |
|---|---|---|
| E11 | Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. | Cycle is paused with door locked. |
| E12 | Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. | Cycle is paused with door locked. |
| E13 | Drain tube improperly positioned; Water pressure too low; Water fill solenoid valve is faulty; Water circuit on pressure switch is leaking/clogged; Pressure switch faulty. | Cycle is paused with door locked. |
| E21 | Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty; Electrical current leak between heating element and ground. | Cycle is paused (after 2 attempts). |
| E22 | Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty; Electrical current leak between heating element and ground. | Cycle is paused |
| E23 | Drain pump faulty; Wiring faulty; PCB faulty. | Safety drain cycle – Cycle stops with door unlocked. |
| E24 | PCB faulty. | Safety drain cycle – Cycle stops with door unlocked. |
| E31 | Pressure switch; Wiring; Main PCB. | Cycle stops with door locked. |
| E32 | Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Water circuit on pressure switch; pressure switch; Wiring; main board. | Cycle is paused. |
| E35 | Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. | Cycle stops. Safety drain cycle. Drain pump continues to operate (5 min. on, then 5 min. off, etc.). |
| E38 | Water circuit on pressure switches; Pressure switches; Motor belt broken. | Heating phase is skipped. |
| E3A | PCB was faulty. | Cycle stops with door locked. |
| E41 | The door lock unit faulty; Wiring is faulty; PCB is faulty. | The cycle is paused. |
| E42 | The door lock unit faulty; Wiring is faulty; PCB is faulty. | Cycle is paused. |
| E43 | The door lock unit is faulty; Wiring faulty; PCB faulty. | (Safety drain cycle) Cycle stops. |
| E44 | PCB is faulty. | (Safety drain cycle) Cycle stops. |
| E45 | PCB faulty. | (Safety drain cycle) Cycle stops. |
| E51 | PCB faulty; current leakage from motor or from wiring. | Cycle blocked, door locked (after 5 attempts). |
| E52 | Motor faulty; wiring faulty; PCB faulty. | Cycle blocked, door locked (after 5 attempts). |
| E53 | PCB faulty. | Cycle blocked, door locked |
| E54 | PCB faulty; current leakage from motor or from wiring | Cycle blocked, door locked (after 5 attempts). |
| E57 | Wiring defective on inverter for motor, inverter board defective. | Cycle blocked, door locked (after 5 attempts). |
| E58 | Wiring defective on inverter for motor, inverter board defective, abnormal motor operation (motor overloaded); Motor defective. | Cycle blocked, door locked (after 5 attempts). |
| E59 | Motor defective; Wiring defective on inverter for motor; Inverter board defective. | Cycle blocked, door locked (after 5 attempts). |
| E5A | Inverter board defective. NTC open (on the inverter board). Overheating caused by continuous operation or ambient conditions (let appliance cool down). | Cycle blocked, door locked (after 5 attempts). |
| E5H | Wiring defective, Inverter board defective. | Cycle blocked, door locked (after 5 attempts). |
| E5C | Inverter board defective, the masters voltage is too high (measure the masters voltage). | Cycle blocked, door locked (after 5 attempts). |
| E5d | Line interference, Wiring defective, defective main board or inverter board. | Cycle blocked, door locked (after 5 attempts). |
| E5E | Defective wiring between main board and inverter board, Defective inverter board, defective main board. | Cycle stops |
| E5F | Defective inverter board, Defective wiring, defective main board. | Cycle stops with door locked (after 5 attempts). |
| E61 | NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. | The heating phase is skipped. |
| E62 | NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. | Safety drain cycle � Cycle stopped with door open. |
| E66 | PCB faulty. | Safety drain cycle � Cycle stopped with door open. |
| E68 | Earth-leakage between heater and earth. | Cycle blocked with door open. |
| E69 | Washing heating element interrupted (thermofuse open) | |
| E71 | Faulty NTC sensor; Wiring faulty; PCB faulty. | Heating is skipped. |
| E72 | Wiring faulty; Drying NTC sensor (condenser) faulty; PCB faulty. | Drying heating is skipped |
| E73 | Wiring faulty; Drying NTC sensor (duct) faulty; PCB faulty. | Drying heating is skipped |
| E74 | NTC sensor improperly positioned; Faulty NTC sensor; Wiring faulty; PCB faulty. | Heating is skipped. |
| E82 | PCB faulty (Wrong configuration data). Selector, wiring | |
| E83 | PCB faulty (Wrong configuration data). Selector, wiring | Cycle cancelled. |
| E91 | Wiring faulty; Faulty control/display board PCB faulty. | |
| E92 | Wrong control/display board; Wrong PCB (do not correspond to the model). | Cycle interrupted. |
| E93 | Incorrect configuration data; PCB faulty | Cycle interrupted. |
| E94 | Incorrect configuration data; PCB faulty. | Cycle interrupted. |
| E95 | PCB faulty. | Cycle interrupted. |
| E97 | Faulty PCB (Wrong configuration data). | Cycle interrupted. |
| E98 | Incompatibility between main board and Inverter. | Cycle interrupted. |
| E9b / E9H | Display board. | Cycle interrupted. |
| E9C | Display board. | Cycle interrupted. |
| E9d | Display board. | Cycle interrupted. |
| E9F | PCB. | Cycle interrupted. |
| EH1 | Power supply problems (incorrect / disturbance); PCB faulty. | Wait for frequency nominal conditions. |
| EH2 | Power supply problems (incorrect / disturbance); PCB faulty. | Wait for voltage nominal conditions. |
| EH3 | Power supply problems (incorrect / disturbance); PCB faulty. | Wait for voltage nominal conditions. |
| EHE | Wiring faulty; PCB faulty. | Safety drain cycle � Cycle stopped with door open |
| EHF | PCB faulty. | Safety drain cycle � Cycle stopped with door open |
| EC1 | Solenoid valve faulty/blocked; PCB faulty. | Cycle interrupted with door closed. Drain pump functions always (5 min., then it stops for 5 min. etc.) |
| EC3 | Wiring faulty; Weight sensor faulty; PCB faulty. | |
| Ed1 | Wiring faulty between PCB and WD board; WD board faulty; PCB faulty. | Cycle interrupted. |
| Ed2 | Wiring faulty between PCB and WD thermostats; WD board faulty; PCB faulty. | The cycle interrupted with door open. |
| Ed3 | Wiring faulty between PCB and WD thermostats; WD board faulty; PCB faulty. | Cycle is interrupted with door open. |
| Ed4 | Wiring faulty: WD board faulty; PCB faulty. | Cycle interrupted with door open. |
| EF1 | Drain tube blocked/kinked/too high; Drain filter dirty/blocked. | Warning displayed at the end of cycle (specific LED). |
| EF2 | Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. | Warning displayed after 5 attempts or by the specific LED. |
| EF3 | Water leaks onto base frame; water control system defective. | Machine drains and cycle stops |
| EF4 | Tap closed, water pressure too low. | |
| EF5 | Final spin phases skipped. |